Ats 01 manual

Then the word END on the display window indicates the end of the programming mode. The real time clock will be showed on the front display window. In the event that power is lost from the normal source, the ATS controller will not start the engine and the ATS cant transfer the load to the standby source automatically. Should you make an error or desire to return to factory settings, stay in programming mode and simultaneously press all 3 buttons : increase , decrease and OFF for 4 seconds.

The ATS controller will now automatically program itself to factory settings and the word Au. Po will appear on the display window. See line by line programming table for ATS factory settings. Any operator associated with programming the ATS controller will quickly discover that ATS controller programming is just a matter of simple. Time delay if there is a problem with standby source voltage output Standby source over frequency setting Standby source under frequency setting Time delay if there is a problem with standby source frequency output Current day of week setting Current hour setting Current minute setting Plant exerciser test day of week Plant exerciser hour Plant exerciser minute Engine run time on exerciser Plant exerciser test with or without load Display mode setting.

The ATS maximum transfer current is 6 Amps,. When the switch transfer current over 6 Amps, two external power relays is recommended. The connecting wire diagram refer to 6. The ATS controller will follow the scale between input volt and key in volt and show the correct voltage on the display window.

Open navigation menu. Close suggestions Search Search. User Settings. Skip carousel. Carousel Previous. Carousel Next. What is Scribd? Explore Ebooks. Bestsellers Editors' Picks All Ebooks. Explore Audiobooks. Bestsellers Editors' Picks All audiobooks. Explore Magazines. Editors' Picks All magazines. Explore Podcasts All podcasts. Difficulty Beginner Intermediate Advanced. Explore Documents. Ats 01 Manual en. Uploaded by ccorrea Document Information click to expand document information Description: manual de ats 01 plantas electricas.

Original Title Ats 01 Manual En. Did you find this document useful? Is this content inappropriate? Report this Document.

Description: manual de ats 01 plantas electricas. Flag for inappropriate content. Download now. Original Title: Ats 01 Manual En. Related titles. Carousel Previous Carousel Next. Electrical Engineering World. Jump to Page. Search inside document. ATS Ver1. Refer to program line 2 When using the ATS module in automatic transfer switch equipment, the switch's intelligence system initiates the transfer when normal power falls below or over a preset voltage or frequency.

Monitor Normal and Standby source over and under frequencies. An automatic transfer switch consists of three basic elements: Permit customer programming display real time information. Main contacts to connect and disconnect the load to the source of power. Refer to program line 29 2. Refer to program line 4 The ATS controller provides the necessary intelligence to insure that the switch operates properly through a series of programmed sensing and timing functions.

TDNE Provide programmable per-exerciser warming signal. Pre-transfer, Pre-exerciser or Transfer fail alarm output. It is divided into four main categories: Standby Source Connected Green Indicates that the transfer switch is connected to the standby source.

With load engine test. Ko Pauk. Gissel CQ. Manuel Otero. Nisar Ahmed. Tirta Budiawan. Juan Araque. Amy Thompson. Lawrence Jimenez. Category: Documents 5 download. The load's normal power source is backed up by a standby emergency power source. A transfer switch is connected to both the normal and emergency sources and supplies the load with power from one of these two sources.

In the event that power is lost from the normal source, the transfer switch transfers the load to the standby source. Once normal power is restored, the load was transferred back to the normal power source.

When using the ATS module in automatic transfer switch equipment, the switch's intelligence system initiates the transfer when normal power falls below or over a preset voltage or frequency. If the emergency source is a standby generator, the transfer switch initiates generator starting and transfers to the standby source when sufficient generator voltage and frequency is available.

When normal power is restored, the transfer switch automatically transfers back and initiates engine shutdown after a preset engine cooling down time delay. An automatic transfer switch consists of three basic elements: 1. Indicates that the standby source is available, and the voltage and frequency are within the programmed parameters. Standby-Power Source Connected Green 4. It is divided into four main categories: Building-Load Connected Green z Automatic mode Indicates that the load is connected to the normal or standby source z Engine test mode z Off mode Normal-Power over Voltage Fault Red z Programming mode Indicates that the normal source is unavailable, and the voltage is over the programmed parameters.

The practical use of each operation under each category will be explained in this section. It is Normal-Power under Voltage Fault Red assumed that prior sections are understood, and the operator has a basic understanding of the hardware.

Indicates that the normal source is unavailable, and the voltage is below the programmed parameters. Normal-Power under Frequency Fault Red The ATS Controller constantly monitor the Indicates that the normal source is unavailable, and condition of both normal and standby power sources, the frequency is below the programmed parameters. Indicating the version of the software.

To change simulates a loss of normal source. When in engine test mode. There are two pre-programmable test increased or decreased by one. The will return to automatic mode. Whatever you change is transfers back from standby source to normal now in memory.

The the present status. See line by line programming table for ATS factory settings. In the event that power is lost from the The first thing the user needs to do is to key in the normal source, the ATS controller will not start real line voltage into the ATS Read the line the engine, and the ATS will not transfer the load to voltage from the normal source from L1 to L3, on the the standby source automatically.

ATS with a good quality digital voltmeter and key-in this volt into the ATS on line 1 in programming When in program mode, pressing the off pushbutton mode.

The rest is easy, follow line by line programming.. Take a voltage reading from You can get out of the incoming normal lines programming mode at LI R to L2 T and remember it any time by pressing the OFF button and holding it for 5 seconds.

Be sure the Normal and Emergency line connections are in proper phase rotation. Place engine generator starting control in the OFF position. Make sure engine generator is not in operation.

User just needs to key in the real voltage Step 1in programming mode values of 6. The ATS controller will follow the scale between input volt and key in volt It is dangerous to feed high voltage to the ATS and show the correct voltage on the display window. Printed Circuit boards. To work at over VAC volts, external power relays are recommended. The we have developed a clear and simple transformer connecting wire diagram refers to 6.

Dimensions L x W x H mm Weight 5. Notes: C NC. UNIT: mm. Open navigation menu. Close suggestions Search Search. User Settings. Skip carousel. Carousel Previous. Carousel Next. What is Scribd? Explore Ebooks. Bestsellers Editors' Picks All Ebooks. Explore Audiobooks. Bestsellers Editors' Picks All audiobooks. Explore Magazines. Editors' Picks All magazines. Explore Podcasts All podcasts. Difficulty Beginner Intermediate Advanced. Explore Documents. Ats 01 - ATS 01E 2.